Masör adam ayaklarından başlayarak kendisini okşayarak sikiş izle devam ettiğinde zevke gelen kumral kız kendisine sikiş yapmasını istedi Genç kız bacakları ayırıp genç adamın kafasını bacakları mobil sikiş arasına aldı Çok çalışkan olmayan asalak gibi yaşayan kızının sikiş daha iyi ders çalışarak geleceğe yönelik bir adım atmasını türk porno isteyen yaşlı anne kızının okuluna gelip sınıf arkadaşları sikiş içindeki en uyumlu olana rica eder ve kendilerine gelip kızıyla porno resim beraber ders çalışmasını rica eder Derslerini daha iyi çalışmaları sikiş izle için önce onların yanında oturup yemek yediren kadın daha sonra mobil porno yanların ayrılınca kaşar kızının aklının derste olmadığını sikiş izle görür Çok asi olan kızı sınıf arkadaşının sikini elleyerek öper
superbahis casino siteleri celtabet

This email address is being protected from spambots. You need JavaScript enabled to view it. | 08458 - 222000

EAMCET| ICET| ECET| CODE: BVRI| PGECET| CODE: BVRI1

Welcome to BVRITN

Mechanical - Publications

Dr. V. Murali Krishna

  1. "Experimental study on the condensation of humid air in laminar flow in a vertical channel" (Article No: HTR-7475), Journal of Heat Transfer Research.Accepted for Publication
  2. "Convective condensation of vapor in laminar flow in a vertical parallel plate channel in the presence of a high con-centration non-condensable gas" ASME Journal of Heat Transfer; American Society of Mechanical Engineering, U.S.A; Jan 2009 Vol. No. 131 pp. 011502-1-7
  3. "Convective condensation of vapor in the presence of a non-condensable gas of high concentration in laminar flow in a vertical pipe" International Journal of Heat and Mass Transfer; Elsevier United Kingdom; Dec 2008 Vol. 51, pp. 6090-6101
  4. “A theoretical study on convective condensation of water vapor from humid air in turbulent flow in a vertical duct” ASME Journal of Heat Transfer; American Society of Mechanical Engineering, U.S.A; Dec 2007 Vol. No.129, pp. 1627-1637
  5. "Pressure Drop and Deposition Rate in Chemical Vapor Deposition – A Theoretical Study on Effect Of System Parameters"; 4-6, January 2010;20th National &9th ISHMT–ASME Heat and Mass Transfer conference. IIT, Bombay, India.
  6. "Experimental Study on Condensation of Water Vapor in The Presence of High Concentration Non-Condensable Gas In Laminar Flow in a Vertical Channel"; 4-6, January 2010;20th National &9th ISHMT–ASME Heat and Mass Transfer conference. IIT, Bombay, India.
  7. "Convective Heat Transfer Characteristics of Sisal-Water Nanofluid in a Shell and Coil"; 27-29, Dec. 2008; 4th BSME-ASME international conference on thermal engineering.
  8. "Theoretical Analysis on Pressure Drop and Heat Transfer in Laminar Flow of a Pseudoplastic Fluid through a Pipe"; 15-17, December 2008; International conference on Advances in Mechanical Engineering NIT, Surat, India
  9. "Condensation of vapor in laminar flow in a pipe in the presence of a non-condensable gas of high concentration - A heat and mass transfer analysis"; January 3 – 5, 2008; 19th National &8th ISHMT –ASME Heat and Mass Transfer conference. JNTU, Hyderabad, India
  10. "Condensation of Vapor in the Presence of a High Concentration Non-Condensable Gas in a Horizontal Parallel Plate Channel under Turbulent flow Conditions"; January 3 – 5, 2008; 19th National &8th ISHMT –ASME Heat and Mass Transfer conference. JNTU, Hyderabad, India
  11. “Condensation of Vapor in the Presence of a High Concentration Non-Condensable Gas during Laminar Flow of Air over a Flat Plate” Held in ITALY; January 4 – 6, 2006; ISHMT–ASME Heat and Mass Transfer conference. IIT Guwahati, India

Mr. S. Ravinder Reddy

  1. High-velocity impact on composite panels of fiber-reinforced plastics using FEM analysis S.R. Reddy, C L Kumar, NJ Kumar and P. JanakiRamulu Proceedings of 1st KIIT International Symposium on ADVANCES IN AUTOMOTIVE TECHNOLOGY page (36-41)
  2. A statistical study on the supply chain in iron foundry C L Kumar, S.R. Reddy, NJ Kumar and P. JanakiRamulu Proceedings of 1st KIIT International Symposium on ADVANCES IN AUTOMOTIVE TECHNOLOGY page (33-35)

Mr. P. Naresh Kumar Reddy

  1. Naresh Kumar Reddy.P, Mahesh.M, and Murali Krishna.K, Optimization of Machining parameters in Electric Discharge Machining using Response Surface Methodology. IJETMAS, 2014, VOL.2 Issue 7, 89-99.
  2. Naresh Kumar Reddy.P and Mahesh.M, Determination of Optimal Cutting conditions using Design of Experiments and Optimization Techniques. IJERT, 2012, VOL.1 Issue 10, 1-10.

Mr. A. Varun

  1. Varun, A., Venkaiah, N., Grey Relational Analysis coupled with Firefly Algorithm for Multiobjective Optimization of Wire Electric Discharge Machining, Part B: Journal of Engineering Manufacture, (DOI: 10.1177/0954405414535591)
  2. Varun, A., Venkaiah, N., Simultaneous optimization of WEDM responses using grey relational analysis coupled with a genetic algorithm, International Journal of Advanced Manufacturing Technology, (DOI: 10.1007/s00170-014-6198-4)